TUTCO DUCT
Accessories
Tutco offers a wide range of duct heater accessories. The control panel is at the heart of any resistive heating solution, playing a crucial role in both performance and safety. A well-designed panel does more than regulate the heater—it optimizes efficiency, extends equipment lifespan, and ensures a secure working environment. On the other hand, a poorly designed panel can cause inefficiencies, premature failures, and potential safety risks. At TUTCO, a proud member of Smiths Group plc, we take this responsibility seriously. Every TUTCO product is engineered to meet the highest quality standards and electrical codes, delivering reliable and safe heating solutions.
CONTACT YOUR CUSTOM DUCT HEATER SPECIALIST
Sydnee Broyles | National Sales Manager
931.432.4141 smiddleton@tutco.com CONTACT CUSTOMER SERVICE
customerservice@tutco.com 
2 Pole Magnetic Contactor
Magnetic contactors are standard in all duct heaters. They are used for primary or back-up control. UL approved for 250,000 cycle operation. Effective 8-4-17, TUTCO will no longer offer mercury contactors due to environmental effects and increased restrictions implemented around the world. We have a full line of magnetic contactors available for standard and custom units.
3 Pole Magnetic Contactor
Magnetic contactors are standard in all duct heaters. They are used for primary or back-up control. UL approved for 250,000 cycle operation. Effective 8-4-17, TUTCO will no longer offer mercury contactors due to environmental effects and increased restrictions implemented around the world. We have a full line of magnetic contactors available for standard and custom units.
Air Flow Switch
The Air Flow Switch prevents the heater from being energized when the fan is not on. Non-adjustable airflow switch requires a minimum of .07” WC pressure. Adjustable airflow switch is available with a rating of .05” ± .02” WC to 12” WC.
Control Transformers
TUTCO Control Transformers are utilized when the control voltage differs from the incoming line voltage feeds. Our Control Transformers provide primary overcurrent protection. Class 1 units must have primary side protection via fusing. Class 2 units have internal protection and do not require additional fusing unless specified.
Electronic Step Controller
An Electronic Step Controller provides smooth sequencing of a duct heater up to 12 steps. When interruption of power occurs all the stages will recycle to OFF. When power is restored, the switches will re-energize in a stepped sequence. Commonly used with a 2–10 VDC from a stand-alone T-stat, 2-10 VDC from a DDC building automation system and 4-20 mA from a building automation system; check with the factory for availability. Not available on DHB & DB series or bottom mount heaters.
Fuse Blocks
TUTCO offers a 3-Position Fuse Block required for NEC code and designed to UL standards. For heaters drawing more than 48 AMPS, contact the factory. Accessory fusing is available on heaters drawing less than 48 AMPS when requested.
Main Power Connector
TUTCO Main Power Connectors are high voltage terminal blocks and sized for copper conductors only. The connector is sized to accept parallel line feeds up to 500 MCM each per pole.
Pilot Light Indicator
TUTCO Pilot Lights are installed in the side panel for indicating the following heater conditions: heater energized, step energized and air flow switch open. Pilot light control voltages must be 24 or 120 volts.
Power Fusing
TUTCO provides Power Fusing to UL standards and NEC code required for heaters drawing more than 48 AMPS. Accessory fusing is available on heaters drawing less than 48 AMPS when requested.
Terminal Block
TUTCO Terminal Blocks are sized for high voltage copper conductors up to a 500 MCM line per pole. Heaters requiring feeders greater than 500 MCM will be supplied with main power terminal blocks which will accept two (2) parallel lines up to 500 MCM each per pole. Low voltage control circuit terminal boards are included for easy field connections.
Time Delay Relay
TUTCO Time Delay Relays provide 30 to 60 seconds when energizing or de-energizing the circuit controlled. The relay can be used with control voltages of 24 to 277.